Clay Processing Equipment

Clay Processing Equipment

How to clean the powder selection duct of the Clay Processing Equipment?

When the air duct is blocked, we should carry out the cleaning work. First of all, we have to look at the structure of the Clay Processing Equipment, because only by understanding its structure and principle, it can be more fully cleaned. Air duct blockage is not a minor issue and must be checked for downtime and appropriate measures taken to resolve the issue. When the feed is too fast, it is necessary to reduce the amount of feed, and sometimes it will alleviate the blockage of the air duct. Generally, a fan or a blower with a relatively large power is required, and the air is blown to the closed air door, and the air volume can be opened to a large extent, and it takes several minutes to clean the air duct.

In the previous article, we explained the working principle and the principle of powder selection of the Clay Processing Equipment in a short language. Using a Clay Processing Equipment as a specific example, the cause of the blockage of the air duct is analyzed, that is, the material humidity and feeding are too fast. Of course, there are many reasons for the blockage of the air duct. We have ruled out the reasons for the mechanical equipment itself and the reasons for the choice of the production line. In that article, in addition to how to avoid the phenomenon of air duct blockage, we also mentioned how to solve this problem after the article, and what can we do after the blockage of the wind tunnel. We can easily make judgments through our life experience, that is, when the air ducts are blocked, we should carry out clean-up work. But how to clean it up? This is also the question raised after the previous article. After reviewing the content of the previous article, let's take a serious look at this question.

First of all, we have to look at the structure of the Clay Processing Equipment, because only by understanding its structure and principle, it can be more fully cleaned. The main components of the Clay Processing Equipment are: 1, the body; 2, the cyclone separator; 3, the cone; 4, the roller lubrication station; 5, the grinding station hydraulic station; 6, the base (air inlet); Reducer; 8, main motor; 9, pressurizing device (hydraulic cylinder); 10, limit device; 11, screw feeder.

After entering the air inlet, the fineness of the finished product size is adjusted according to the size of the wind, and then the powder is selected by the cyclone separator. In this process, if the material is too humid or the feed is too fast, or for other reasons, the air duct is blocked. At this time, the general practice is to stop the cleaning carefully, and if it is cleaned, it is to choose the powder.

What needs to be known is that the blockage of the air duct is not a minor problem. It is necessary to carry out a shutdown check and take appropriate measures to solve the problem. Next, we will talk about the air duct. The air duct is the outer casing for installing the grinding ring. It is also the processing channel for the swirling air volume. It is very necessary to participate in the powder selection operation almost all the way. During the grinding of the material by the Clay Processing Equipment, it is sometimes necessary to process some materials with a higher water content. In such a situation, the normal practice is to dry the material and then perform the milling operation, but sometimes the water content is not well grasped, or the viscosity of the material after the powder is high, resulting in a serious problem of air passage blockage.

Another common situation is that the feed is too fast. When feeding the Clay Processing Equipment, there is a certain difference from the crushing equipment, especially the Clay Processing Equipment, which is a vertical structure, and the materials are generally transported to the high place via the electromagnetic vibrating feeder, and then from the feed port. It falls into the machine cavity and is ground. When the feed is too fast, it is necessary to reduce the amount of feed, and sometimes it will alleviate the blockage of the air duct. However, there are quite a few situations where it is not possible to solve this problem by reducing the feeding. Then a direct method is needed, which is to clean directly.

When you are ready to clean the appliance, first make sure that the equipment is disconnected from the power supply and that there are no abrasive materials in the mill chamber. Then open the door in the grinding chamber, clean out the spilled material, and then open the three closed doors outside the air duct to remove the material. At this time, there is little left in the air in the air duct, but the material attached to the wall of the air duct has not been cleaned up. The shovel or iron hook is required to clean the powder from the duct wall. It is worth noting that if you only use these tools, you can't clean them up. Generally, you need a fan or blower with a relatively high power. When you close the air blower, the air volume can be turned on and it will last for a few minutes. The air duct is cleaned up.

In the daily use of the Clay Processing Equipment, the basic maintenance method of the equipment needs to be very familiar and regular training is required. In this way, when an abnormal situation occurs in the device, the problem can be captured very sharply, and the correct judgment and operation can be made at the first time. This not only enables the production to be carried out safely and smoothly, but also ensures personal safety and also improves production efficiency.

The blockage of the Clay Processing Equipment duct is somewhat troublesome to clean up because of the somewhat complicated structure. Therefore, in the normal use process, it must be strictly in accordance with the operation manual, and pay attention to the timely cleaning process, can not wait until the air passage is blocked, the cleaning operation is not performed, which not only makes the equipment work in low efficiency and high risk for a long time. In the environment, and when cleaning up, it is quite troublesome.

Other Case

Raymond Mill
Raymond Mill

Market of Complete Stone Raymond Mill In PhilippinesPhilippine Science Technology in constant development, the industry’s needs are growing, customers need hig


LEAVE YOUR MESSAGE
Popular Products
Construction Waste Crusher

Used Portable Construction Waste CrusherWhile using the urbanization process, growing the yield soaring construction waste, it's also introduced having a large

Quarry Crusher

Market of Used Portable Concrete Quarry Crusher in ChinaIn line with the Secretary of condition for Railways to develop a “long-term railway network plan,” 20

Gold Ore Crusher

Low Intensity Gold Ore Crusher Supplier in NigeriaLow Intensity Gold Ore Crusher is among the most engine of financial development, while using rapid progressio

Sand Washing Machine

China Rotary Tube Sand Washing Machine Development TrendFirst, Rotary Tube Sand Washing Machine Bigger Trend.Mainly for your mill, China has clearly introduced

Ultrafine Mill

Market of Kenya Small Aggregates Ultrafine MillWhile using current industry to market the ceaseless progression of numerous metals, non-metallic minerals for in

Ore Milling Equipment

Hammer Ore Milling Equipment With CycloneLately, the SBM Machine within the introduction, absorption of foreign advanced technology, according to innovative dev

Stone Crushing Equipment

Nigeria Used Small Hammer Stone Crushing Equipment Publication rack HotAccording to SBM sales personnel, Used Small Hammer Stone Crushing Equipment is actually


Recently updated

Raymond Mill

Market of Complete Stone Raymond Mill In PhilippinesPhilippine Science Technology in constant development, the industry’s needs are growing, customers need hig